高地压严重突出区域下向穿层钻孔预抽消突技术

利用工作面高抽巷施工掩护顺槽掘进工作面下向穿层条带预抽钻孔,通过对钻场底板深、浅孔注浆封堵围岩裂隙解决了孔内返水不畅难题;采取了"两堵一注"封孔方式确保封孔严密不漏气;孔内全程下吹水管,实现了单孔、分组、定时吹水工作目标,提高了下向消突钻孔抽采效果,形成了一套高效、快速的下向穿层钻孔消突管理模式,实现了高地压严重突出区域煤层高效消突以及技术经济一体化目标,安全经济效益显著。     

车辆高速避让路径跟踪控制策略

建立车辆动力学模型,研究车辆在高速避让工况下的路径跟踪控制策略。基于自抗扰控制设计车辆横摆角速度以及道路曲率2种不同的路径跟踪控制器;设计基于车辆偏航位移和偏航角度加权的线性二次最优控制器;对3种控制器控制效果进行仿真验证,分析路径跟踪侧向位移误差、侧向加速度、前轮转向角以及偏航角度变化。越野车实车测试结果表明,路径跟踪控制策略正确。     

牵引车载荷对NOx排放和排温影响的试验研究

在五轴动力总成试验台架上对牵引车在不同载荷下进行同一路谱的排放试验,研究牵引车在不同载荷下NOx排放和排温的变化,得到载荷与排放物和选择性催化还原(selective catalytic reduction,SCR)上游排温的变化关系。结果表明:载荷为标定载荷的60%以下时,NOx比排放值与载荷基本呈线性相关;载荷超过标定载荷的75%时,NOx比排放值与载荷呈二次项相关;载荷在为标定载荷的23%以上时,NOx比排放值与SCR上游排温基本呈线性相关。利用该试验结论可以通过只进行单一载荷排放试验,判断车辆在其他载荷下的排放水平是否满足国家标准要求,并可通过载荷对排温的影响规律预判排放水平。     

空冷器用高压水清洗与雾化降温系统集成设计与开发

高压水清洗系统和喷淋降温系统分别是春季保持空冷器翅片表面清洁和夏季保证空冷器在高温下正常运行的2个重要辅助系统。针对喷淋系统的缺点研究了高压射流雾化技术,通过试验论证了高压水清洗与雾化降温系统集成的可行性和合理性。根据设计思路开发的集成系统已在山西某项目获得应用并取得了良好的使用效果,此高压水清洗与雾化降温集成系统中高压水发生装置及介质输送管路共用,产生的高压水射流雾化颗粒可达到60μm,夏季降温效果较传统喷淋降温效果大幅提升,水资源的利用率得到极大提高,系统性价比更高。     

ASME Ⅱ卷D篇表U数据作为设计校核中材料验收标准存在问题及探讨

ASME标准钢板对于短时高温抗拉数据无规定,但设备设计人员在校核时又要用到此数据,于是有些设计文件在技术要求中将ASME II卷表U的数据作为材料验收的标准。针对此种做法引发的争议及涉及的主要问题进行试验验证和分析探讨。研究结果表明,ASME II卷D篇表U中的数据是基于室温抗拉强度保证值,并根据拟合曲线将室温保证值提高了10%得到的,实测数据与ASME规范数据不一致,部分材料在250~350℃存在动态应变时效现象,但仍不满足设计要求。材料经模拟焊后热处理后性能下降,难以到达交货态的要求。给出了短时高温抗拉强度的选用建议。     

高泉背斜地层压力测井多参数综合解释与异常高压成因

目前国内外地层压力测井解释方法较多,但大多数方法基于欠压实沉积理论并局限于单一的地层岩性,尤其是针对盆地边缘山前深层构造,单一测井参数确定地层压力误差较大,且无法解释沉积压实机制以外的异常高压。为此,将多种异常高压机制相关的测井参数进行综合解释,建立适合山前复杂构造的地层压力测井多参数计算模型,评价准噶尔盆地南缘高泉背斜高探1井的地层压力剖面,其计算结果与钻井实测数据吻合,相对误差小于3.00%.同时,基于原始沉积加载—卸载过程力学原理,利用地层压力测井多参数分析判别出高泉背斜深层各层系异常高压的形成机制。     

浅谈不同给液方式在铜电解车间的应用

不同给液方式对铜电解过程中有重要的影响,不同的循环方式会影响槽内温度分布、电解液成分及阳极泥沉降等,因此,根据铜电解生产不同情况的需要,分析对比了多种给液方式在贵冶电解车间的应用,总结了这几种给液方式的优缺点和适用条件。     

一种压电半导体纳米线的热电耦合性能研究

采用有限元分析方法,研究了一种n型压电半导体纳米线(氧化锌)的电热耦合性能,分析了外部温度对氧化锌纳米线内部机械场、电场及电流场分布的影响,并讨论了本构方程线性化对电学参数的影响。研究结果表明,温度对氧化锌纳米线的电场、载流子浓度和电流密度影响很大,采用线性本构和非线性本构求得的电场、电子浓度和电流密度最大相差分别为24%,32%和68%,基于非线性本构分析压电半导体的电学性能会引起很大误差。该研究结果可为压电半导体器件利用温度调控电场、电流提供理论依据。     

Effect of high temperature and separated combustion on SO2 release characteristics during coal combustion under O2/CO2 atmosphere

This paper studied the effect of high temperature (up to 1873K) and separated combustion mode (volatile combustion and char combustion are separated) on SO₂ release characteristics during pulverized coal combustion under O₂/CO₂ atmosphere. Coal combustion experiments were conducted at different combustion environment temperatures utilizing a high temperature fixed-bed setup. The results show that as temperature rises, the SO₂ release curve is transformed from a single-peak process to a double-peak process. In separated combustion, temperature has little effect on the volatile-SO₂ (SO₂ released during volatile combustion) but brings about a significant effect on char-SO₂ (SO₂ released during char combustion). Char-SO₂ release amount and the ratio of it to fuel-SO₂ release amount (total SO₂ released during coal combustion) increase with temperature rising. The increase of temperature leads to a dramatic decreasing of sulphur mass fixed in the ash and causes SO₂ release amount to rise when temperature is lower than 1573 K. Separated combustion causes a higher SO₂ release amount than coupled combustion (the same as conventional combustion, volatile combustion and char combustion are simultaneous). Thermochemistry equilibrium composition calculation results show that alkali metals and alkaline-earth metals are significant in sulphur retention. CaSO₄ and Na₂SO₄ are the main sulphates at high temperatures.     

Design and characteristics of a new type laminar plasma torch for materials processing

Laminar plasma jet(LPJ) generated by laminar plasma torch(LPT) has a favorable temperature and velocity distribution. Thus, it is superior to the turbulent plasma jet in material processing.However, most of the reported LPTs usually operate at a relatively low output power with a relatively low arc voltage and thermal efficiency, which limits its capabilities. In this context, this paper attempts to design a new type of high-power LPT with a relatively low arc current and a high thermal efficiency. In the first section, the design principle of the main components is studied and discussed in detail, and a new high-power LPT is proposed. Then, the experimental characteristics of the proposed high-power LPT are examined. Experimental results reveal the following characteristics of the proposed LPT.(1) The max jet length of the proposed LPT reaches at 540 mm.(2) Its mean arc voltage is higher than 290 V when the LPT works with arc currents lower than 200 A, leading to an output power greater than 50 kW.(3) The mean thermal efficiency is higher than 50%. Lastly, the proposed LPT has been applied to spheroidize the aluminum oxide powers. The experiment results for the production of spherical powders show that the proposed LPT has a good characteristic for material processing.